Compatibility : 1998-2003 Mercedes-Benz ML320 3.2L2003-2005 Mercedes-Benz ML350 3.7L2000-2001 Mercedes-Benz ML430 4.3L2002-2004 Mercedes-Benz ML500 5.0L2000-2003 Mercedes-Benz ML55 AMG 5.5L1996-1999 Mercedes-Benz S600 6.0L Features: 4pcs 98-03 for Mercedes-Benz ML320 3.2L 02 O2 Oxygen Sensor Upstream Downstream
Compatibility :
1998-2003 Mercedes-Benz ML320 3.2L
2003-2005 Mercedes-Benz ML350 3.7L
2000-2001 Mercedes-Benz ML430 4.3L
2002-2004 Mercedes-Benz ML500 5.0L
2000-2003 Mercedes-Benz ML55 AMG 5.5L
1996-1999 Mercedes-Benz S600 6.0L
Features:
- Porous PTFE Filter - Allows atmospheric oxygen to enter the sensor without permitting water or engine contaminants to seep into the casing.
- Double Protection Cover - Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
- Stainless Steel Housing - Resists corrosion and contamination with a rugged, watertight body.
- Aluminum-Oxide Trap Layer - Keeps silicone and lead outside the ceramic elient through, preventing damage to the platinum electrode.
Whereistheoxygen sensor in your vehiche?
Whow to install an oxygen sensor?
1.Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it.
2.Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart.
3.Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it.The majority of oxygen sensors will take an SAE7⁄8inch (2.2cm) wrench.
4.Compare your new oxygen sensor to the old one.If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work.
·Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors.
·Use heat sensitive shrink tape to seal the connections.
·Follow manufacturer's instructions to know which wires to tie together.
5.Reverse the steps used in removing the oxygen sensor and install the new part.Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads.
6.Plug the electrical connections back in.
7.Turn on the ignition key, but do not start your vehicle.Use the diagnostic scanner/reader to clear the code from the vehicle's computer.
8.Start the car.You should notice an immediate improvement.
NOTE:
If you can't determine whether the oxygen sensor fit your vehicle or not, please contact us.
Item SpecificsBrand imcarpartsManufacturer Part Number IM991780CARManufacturer Warranty 1 YearFitment Type Direct ReplacementCustom Bundle YesModified Item NoType SensorNumber of Pieces 4Wire 4Position Upstream, DownstreamHousing Material MetalThread Size 18 X 1.5 MMUniversal Or Specific Fit SpecificAutomotive Color / Finish SteelTerminal Type BladeAttachment Method Screw-OnOutput Signal Range (V) 0.2 To 0.8 VoltFeatures Direct FitAttachment Method Screw-OnOutput Signal Range (V) 0.2 To 0.8 VoltType SensorFeatures Direct Fit
Payment
Payments are expected within 7 days after the last winning sale is closed; Otherwise Unpaid Item Dispute will be filed with .
Shipping 1. Orders processed within 24 hours of payment verification.2. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!Returns We offer a 30 days Free Return
Contact Us
We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)
4pcs 98-03 for Mercedes-Benz ML320 3.2L 02 O2 Oxygen Sensor Upstream Downstream
Compatibility :
1998-2003 Mercedes-Benz ML320 3.2L
2003-2005 Mercedes-Benz ML350 3.7L
2000-2001 Mercedes-Benz ML430 4.3L
2002-2004 Mercedes-Benz ML500 5.0L
2000-2003 Mercedes-Benz ML55 AMG 5.5L
1996-1999 Mercedes-Benz S600 6.0L
Features:
- Porous PTFE Filter - Allows atmospheric oxygen to enter the sensor without permitting water or engine contaminants to seep into the casing.
- Double Protection Cover - Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
- Stainless Steel Housing - Resists corrosion and contamination with a rugged, watertight body.
- Aluminum-Oxide Trap Layer - Keeps silicone and lead outside the ceramic elient through, preventing damage to the platinum electrode.
Whereistheoxygen sensor in your vehiche?
Whow to install an oxygen sensor?
1.Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it.
2.Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart.
3.Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it.The majority of oxygen sensors will take an SAE7⁄8inch (2.2cm) wrench.
4.Compare your new oxygen sensor to the old one.If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work.
·Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors.
·Use heat sensitive shrink tape to seal the connections.
·Follow manufacturer's instructions to know which wires to tie together.
5.Reverse the steps used in removing the oxygen sensor and install the new part.Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads.
6.Plug the electrical connections back in.
7.Turn on the ignition key, but do not start your vehicle.Use the diagnostic scanner/reader to clear the code from the vehicle's computer.
8.Start the car.You should notice an immediate improvement.
NOTE:
If you can't determine whether the oxygen sensor fit your vehicle or not, please contact us.
Item SpecificsBrand :imcarpartsManufacturer Part Number :IM991780CARManufacturer Warranty :1 YearFitment Type :Direct ReplacementCustom Bundle :YesModified Item :NoType :SensorNumber of Pieces :4Wire :4Position :Upstream, DownstreamHousing Material :MetalThread Size :18 X 1.5 MMUniversal Or Specific Fit :SpecificAutomotive Color / Finish :SteelTerminal Type :BladeAttachment Method :Screw-OnOutput Signal Range (V) :0.2 To 0.8 VoltFeatures :Direct FitAttachment Method :Screw-OnOutput Signal Range (V) :0.2 To 0.8 VoltType :SensorFeatures :Direct Fit
PaymentShippingReturnsContact Us
Payments are expected within 7 days after the last winning sale is closed; Otherwise Unpaid Item Dispute will be filed with .
1. Orders processed within 24 hours of payment verification.2. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! We offer a 30 days Free Return
We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)
All right reserved.
Shop CategoryStore Home Secondary Air Pump Door handle LED Headlight Assembly JeepHot Item For 1998-03 Toyota Sienna Door Handle Interior Front Left Driver Side Beige USD 12.09 For 2008-2013 Toyota Highlander Set Roof Rack Rails Cover End Shell Replace USD 22.04 For 00-04 Toyota Avalon 1Pc Door Handle interior Left Driver Side Inside USD 11.09 For GM New 4WD Transfer Case Shift Motor Encoder w/RPO Code NP8 600-910 USD 73.19 Alternator For Chevrolet 1973-1989 1 Wire 12V 110A 7127-SE105C 7127NSE-100A-C USD 76.55 New List Item AC Compressor For Mercedes-Benz ML350 3.5L 2013 W/ Clutch USD 124.32 Front or Rear Wheel Hub Bearing For Mercedes-Benz A220 A35 AMG GLA35 AMG AWD USD 53.99 Power Window Regulator For BMW X3 2010-04 749-498 749-499 Front LH RH USD 61.99 Power Window Regulator For 1998-2005 VW Passat 740-368 740-369 Front LH RH USD 79.99 Set(2) Front or Rear Wheel Hub Bearing For Mercedes-Benz A220 A35 GLA35 AMG AWD USD 89.99 Help & InfoPayment PolicyShipping PolicyReturn PolicyFAQAbout Us
